Product Manuals & App Setup

• Charge your batteries. Fully charge all battery modules before first use. Chameleon X runs on a dual-battery system for longer run time, and a digital display shows the exact charge percentage so you always know the level.
• Connect power cables. Inside your garment you'll find the power connectors — check each pocket and make sure every connector is firmly attached.
• App control required. Chameleon X is controlled through the LED Chord app.
• The battery button. The module button only turns the last saved preset on/off — it does not change colors or modes. Use the app for everything else.

• Never fold against the fibers. Don't fold the fiber-optic fabric perpendicular to the fiber direction, and don't press, sit, or lean on a fold — force or hard pressure there creates permanent creases that can break the fibers.
• Avoid pulling & twisting. Don't stretch, twist, or force the garment into tight spaces.
• Protect from pressure. Don't apply heavy pressure to lit areas.
• Recharge promptly. Dim lights mean a low battery.
• Warranty note: manufacturer defects are covered for 1 year. Damage from misuse or sharp bending is not covered.

• Connecting: place each battery in its pocket first, then connect the cable.
• Removing: disconnect the cable first, then remove the battery.
• This prevents tension on the wiring and ports.

Cleaning is the same as the YMYW Collection. Always remove the battery modules and electronics first.

For a full clean:

• Hang the garment on a hanger.
• Spray it inside and out with warm water and a little mild detergent.
• Wait 15–20 minutes.
• Rinse gently with a shower head (warm water).
• Hang to dry in the shade until 100% dry, then reconnect the batteries.

For small marks, just wipe with a soft damp cloth and a little mild detergent.

Never machine wash, tumble dry, wring or twist the fiber-optic fabric.

• Avoid high humidity, dust, direct UV, high-energy light sources, and chemicals (gasoline, solvents, plasticizers, ethyl acetate, PVC, etc.).
• Store in a dry, ventilated, waterproof location.

• Safe operating range: −10°C to +50°C.
• High heat can warp the fabric; extreme cold can make fibers brittle.

The garment is lightly water-resistant — the fabric can get wet, the batteries cannot.

• If it rains: turn the batteries off, remove them, and store them dry.
• Reconnect once everything is fully dry.

The LED Chord app gives you 16 million colors, 32,000+ presets, brightness and speed control, sound-reactive effects, and custom patterns across the whole garment.

• Lights won't turn on? Check both batteries are charged, cables are firmly connected, and hold the ON button 1–2 seconds.
• Lights flickering? A battery is low — recharge; check the cables; make sure the garment isn't bent sharply.
• App not connecting? Restart the battery module, restart the LED Chord app, and make sure Bluetooth is on and your phone is close.

• Hang to store, avoid compression, clean gently, and charge batteries about once a month even when not in use.
• Covered by the YMYW Quality Warranty: manufacturing defects in electronics, wiring and construction under normal use for 1 year.
• Help or replacement parts: [email protected] · YMYW, Las Vegas, NV. Returns/exchanges within 14 days.

• Dual-style reversible coat — two premium designs in one, fully wearable on both sides.
• Smart LED system — 260+ ultra-bright LEDs, app-controlled (iOS + Android), 16 million colors, 120 dynamic presets, adjustable speed and brightness.
• Premium materials — two layers of 4-way stretch fabric (400g each), trimmed with plush cruelty-free fur.
• Storage — 6 deep zip pockets total (2 hidden side-seam zips), one Velcro power-bank pocket, one receiver compartment.
• Practical design — smooth reversible zippers, built for dancing, festivals, travel and city nightlife.

• YMYW LED Light-Up Reversible Coat
• LED controller with Bluetooth receiver
• Internal wiring system (pre-installed)
• USB power cable (for the power bank)
• Care & safety instructions
• Power bank included.

• Step 1 — Find the power pocket. On one side of the coat, locate the deep Velcro-closing pocket where the power bank sits.
• Step 2 — Connect the USB cable. Plug the coat's USB connector into your power bank and place it in the Velcro pocket.
• Step 3 — Turn on the LEDs. As soon as power is supplied, the LEDs light up in the default mode.
• Step 4 — Connect the app. Inside the interior seam you'll find the Bluetooth controller with a QR code. Scan it, download the recommended app, open it and connect, then control colors, presets, brightness and speed.

• In the app: 16M color wheel, 120 lighting presets, strobe / pulse / fade animations, speed and brightness sliders.
• Manual mode: turn the coat on without the app and the last used preset displays automatically.

• Flip the coat inside-out.
• Make sure pockets and wiring sit comfortably.
• Wear and enjoy the alternate design.

This version is machine-wash safe when the guidelines are followed.

Before washing — you MUST:

• Disconnect the 3 small wire connectors from the LED controller.
• Remove the Bluetooth receiver module.
• Remove the power bank.

Never wash the coat with electronics attached — it can cause permanent damage.

• Machine washing: gentle cycle, cold or warm water, mild liquid detergent, wash alone or with similar soft fabrics.
• Drying: machine dry on delicate/low heat, or hang dry.
• Reconnect electronics only when the coat is 100% dry, inside and out.

• Operate using 5V power banks only.
• Don't expose electronics to rain, snow or moisture. If caught in rain: turn off the power bank, disconnect the USB cable, and store the power bank in a dry bag.
• Don't sleep in the coat while powered.
• Keep away from open flames and heaters.
• Inspect the wires occasionally. The coat is lightly water-resistant; the electronics and power bank are not.

• Store on a hanger to keep its shape.
• Keep electronics in the inside pocket when not in use.
• Avoid crushing the coat when electronics are connected.
• Brush the faux fur gently to keep it soft.
• For travel, disconnect electronics and pack them separately.

• LEDs won't turn on? Check the power bank charge, the USB cable connection, and that the 3 wire connectors are plugged into the controller.
• App not connecting? Turn Bluetooth on, keep the phone close to the controller, restart the app, restart the power bank.
• Lights flickering? Low power bank or a loose connector — re-secure the wiring.

• Covered by the YMYW Quality Warranty: defects in electronics, wiring and construction under normal use for 1 year.
• Support or replacement parts: [email protected] · YMYW, Las Vegas, NV. Returns/exchanges within 14 days.